Hamlet HPS01PP2 Manual do Utilizador

PARALLEL PRINT SERVER NETWORK DATA TRANSFER RATE 10/100MBPS User Manual HPS01PP2 www.hamletcom.com

10 3 Software Installation The PSAdmin is a proprietary Windows-based management program that can assist you in configuring and managing your print se

11 3. Choose Setup Wizard to install the print server and configure the connected printer. Note: The setup CD will install the print server’s driver

12 5. From the Select A Print Sever screen, select the print server that you want to configure and click Next.

13 6. On the Change Settings screen, select No or Yes: Click No if you want the print server to keep using the default IP address and keep the defau

14 7. In the setup wizard, select an already configured printer from the list, click Next, Next and then Finish to complete the installation. or Sele

15 8. Click Add New Printer to launch Windows Add Printer Wizard. 9. Click Next and select Local Printer, make sure the Automatically detect and in

16 10. Make sure the Use the following port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down list. Then click Ne

17 12. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the p

18 15. From Windows system, go to start -> Printers and Faxes and highlight your newly installed printer. 16. Right-click, select Properties -&

19 17. Go to General; click Print Test Page to verify the configuration. 18. Done. Note: If you want to install more print servers, start setup wiza

2 Dear Customer, thanks for choosing an Hamlet product. Please carefully follow the instructions for its use and maintenance and, once this item has r

20 Wizard Wizard is a configuration program that can assist you in setting up the necessary parameters for your print server device to function. Setup

21 5. (Optional) In the Gateway field, type the IP address of gateway. 6. When done, click OK button. The program will save the above settings into

22 Manual Setup Manual Setup is a configuration program designed for more experienced users of NetWare. To setup the print server by using Manual Setu

23 Properties – TCP/IP Options The TCP/IP options allow you to modify the print server’s TCP/IP settings. Each option is detailed as follows. Obtai

24 Upgrade Upgrade allows the user to upgrade the print server device. In order to upgrade the unit please perform the steps as follows: 1. Click Upg

25 Multiple Print Queues Configuration To configure the print server to service multiple print queues, please follow the instructions listed below: 1

26 4 Internet Printer Connection and HP Web JetAdmin IPP Overview Print server(s) support the Internet Printing Protocol (IPP). Using the appropriate

27 7. It will check print server to connect to HP printer, if not, it will appear as follow picture. Then Click OK. 8. Select the appropriate pri

28 HP Web JetAdmin Overview HP Web JetAdmin allows you to use a Web browse to revise, view, manage and diagnose devices connected to the print server

29 Removing HP Web JetAdmin Utility To remove HP Web JetAdmin software from your web server, use the uninstall program provided with the software pack

3 Table of Contents 1 Introduction...

30 5 Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that can be accessed through a supported web br

31 System Status 1. Click Status, it then appears the sub-menu. 2. Click System, it then as shown in the following picture. Print Server Name: This

32 Printer Status 1. Click Status, it then appears the sub-menu. 2. Click Printer, it then as shown in the following picture. Manufacturer: This opt

33 TCP/IP Status 1. Click Status, it then appears the sub-menu. 2. Click TCPIP, it then as shown in the following picture. Use DHCP/BOOTP: This opti

34 Netware Status 1. Click Status, it then appears the sub-menu. 2. Click Netware it then as shown in the following picture. General Settings Prin

35 NetWare Bindery Setting Use Bindery Mode: Enable or Disable. Name of the File Server: Current Status: Connect or Disconnect.

36 AppleTalk Status 1. Click Status, it then appears the sub-menu. 2. Click AppleTalk, it then as shown in the following picture. AppleTalk Settings

37 SNMP Status 1. Click Status, it then appears the sub-menu. 2. Click SNMP, it then as shown in the following picture. SNMP Communities: This optio

38 SMB Status 1. Click Status, it then appears the sub-menu. 2. Click SMB, it then as shown in the following picture. Workgroup Name: This option

39 Setup Menu Meanwhile, you have finished the IP address configuration with print server. You should use web browser to configure the print server.

4 Installing Print Server on NetWare 4.x/5.x... 45 AppleTalk Setup...

40 Email Alert: This option allows you to Enable/Disable the Email Alert support. SMTP Server IP Address: This option allows you to input the IP addre

41 Printer Setup 1. Click Setup, it then appears the sub-menu. 2. Click Printer, it then as shown in the following picture. Bi-directional Settings

42 TCP/IP Setup 1. Click Setup, it then appears the sub-menu. 2. Click TCP/IP, it then as shown in the following picture. DHCP/BOOTP: This option al

43 NetWare Setup 1. Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Select NetWare and type in the Print server that cr

44 Polling Time: The time interval in which the print server unit polls the file server for servicing of print queues. Logon Password: This option all

45 Installing Print Server on NetWare 4.x/5.x Due to its architecture and functionality, the print server must work under NetWare 4.x/5.x NDS Bindery

46 AppleTalk Setup The print server can print jobs submitted from Macintosh workstations connected to an Ethernet using AppleTalk protocol. The basic

47 Note: The default print server’s Chooser name is as shown as follows: <ATALK_PS>-xxxxxx-1, where xxxxxx represents the last six digits of th

48 SNMP Setup TCP/IP networks use a standard management protocol called Simple Network Management Protocol (SNMP). SNMP is widely used in the industry

49 snmp.snmpEnableAuthenTraps Enables or disables the function of sending SNMP Authentication Failure trap message to the network administrator, if

5 1 Introduction Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly on

50 SMB Setup The print server supports the SMB (Server Message Block)protocol, user can send the print jobs through Network Neighborhood without insta

51 6 Network Print Monitor Preparation The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Microsoft Windows system. Please make su

52 Note: Using TCP/IP protocol to access the print server requires well-configured TCP/IP settings. If you are not familiar with these settings, pleas

53 Windows 95/98/Me/NT/2000/XP/2003 manual Installation Procedure Please perform the steps as follows to ensure a smooth installation: 1. Run Setup f

54  By default, the computer will first search for the print server(s) on the network by using the IPX/SPX protocol.  If the IPX/SPX protocol i

55 Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP/2003 To provide users an easiest way to remove all of the Network Print Port compone

56 7 TCP/IP LPR Port Printing Installation Basic TCP/IP Installation Overview When installing your print server in a TCP/IP environment, IP addresses

57 6. The Add LPR compatible printers box will then appear as shown in the following picture. Type in the IP address assigned to the print server i

58 Windows 2000/XP/2003/Vista/7 Standard TCP/IP Port Printing Installation 1. Click Start, point to Settings, and select Printer. 2. Run Add Printer,

59 6. In the Add Standard TCP/IP Printer Port Wizard box as shown in the following picture, Select Custom, Click Settings button, and click Next. 7

6 LED Indicators LED State Indication Status Blinking for POST (Yellow) When power switched on, the Status indicator will flash five times, and t

60 12. A message reading, “To confirm that the printer is installed properly, you can print a test page”. Select Yes (Recommended) and click Finish. 1

61 UNIX Installation After the static IP address is assigned, the Print Server is ready to be configured. For some UNIX/Linux systems, we include the

62 Redhat Linux 9 (Fedora) The Print Server can work under any Linux-based systems, including Slackware, RedHat, etc, without any problems. Basically

63 7. In the Name field, type a user-defined name, click Forward. 8. In the Queue Type field, choose Networked UNIX. 9. In the Server field, type

64 12. In the Printer field, choose Postscript Printer. 13. Choose the model of printer and click Forward. 14. Done.

65 8 Upgrading Print Server Overview Upgrading print server will allow you to upgrade its firmware inside the print server while the newer software ve

66 Upgrading the print server from UNIX (Through TCP/IP) 1. Log in as root 2. Ensure binary file is located in your current working directory. 3. Ty

67 9 Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in thi

68 need to implement the following procedures in order for your print server to function properly: • Add the RIP for NWLink IPX/SPX compatible trans

69 Moving the print server to A New Segment If the print server is moved from one network segment to another after the initial installation, through t

7 Network Environment Wired Network with Print Server PrinterPrint ServerComputer Computer ComputerHUB

70 Moving Your Computer to A New Segment If you are using the print server through the Network Print Port on your NT or Windows 95/98/Me computer and

71 B. The print server's IP address is duplicated or is as same as another computer's IP address on the network. If this is the case, pleas

72 file and quit from your editor. Please note, in this step you must specify an IP address which is valid on Segment B, such as 192.72.214.100 in thi

73 Appendix SMB Printing with Windows XP 1. Enable the SMB settings from the print server’s WEB configuration. Assume your computers use the “WORKGROU

74 2. Now you can find the print server from the SMB workgroup of Windows. Then, double click it. 3. Double click it again.

75 4. Now you have to install the printer’s driver. 5. Choose it from the “Add Printer Wizard”.

76 6. Install printer successfully. 7. Now, you can find your printer’s icon and you can use the SMB printing mode.

77 Reset Button Reboot the Print server 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it. WARN

78 Frequently Asked Questions Question A Print jobs are sent to the print queue successfully, but fail to be sent to the printer. Possible explanatio

79 Question D The Status LED light keeps blinking after POST. Possible explanation and solution The last upgrade process was not completed. The prin

8 2 Print Server Installation Preparation To meet users’ network printing needs in today’s heterogeneous and multiple protocol networking environments

9 Internet Printing Protocol Windows NT/2000/XP/2003/Vista/7 Printing via the internet to Internet Printing Protocol- enabled print server Allows savi